X-Fusion Trace 36 29" HLR Boost Fork
- ShowProduct Information Developed for the new progression of 29er super enduro bikes with 170mm travel and 36mm stanchions, ... read more
- Show Customer Reviews (0)
- Show Suspension Forks Sizing
- Show Suspension Forks Guide
- Show Finance
- Show Delivery & Guarantee
Developed for the new progression of 29er super enduro bikes with 170mm travel and 36mm stanchions, the X-Fusion Trace 36 29" HLR Boost fork offers a stout chassis with smooth and efficient damping.
The Trace36 HLR Boost fork is available with the Roughcut HLR bladder cartridge damping system, riders will no longer have shy away from the most technical bits of trail but will be looking for what they can conquer next.
- The Roughcut Damper is a fully bled bladder and cartridge based damper which features high and low speed, independently adjustable compression and rebound damping adjustment.
- Nvolve Wiper seals reducing seal drag and increasing durability.
- Weight: 2110 grams
- Wheel Size: 29 inch
- Travel: 170mm, (ITA 140/160/170)
- Stanchion: 36mm Aluminium
- Spring: Air
- Damper: Roughcut HLR
- Adjustments HLR: High and Low Speed Comp., Rebound,, Air Pressure
- Steerer: Tapered only
- Axle: bolt-On Boost 110*15mm
- Color: Flat Black
- Axle to Crown: 581mm @ 170mm
- Offset: 51mm
- Rotor Size: 180~ 203mm(XF adaptor only)
Occasionally, without notice, manufacturers change product design and/or specifications.
There are currently no customer reviews
Suspension Forks Sizing
Suspension Forks Sizing
A new suspension fork is one of the most noticeable and worthy upgrades you can make to your mountain bike. A higher quality fork will be able to deal with more difficult terrain, remaining composed on the trail and keeping your wheel in contact with the ground. This gives more grip, and therefore a more confidence inspiring ride.
Not all forks are made equal, there are some very important size and compatibility aspects to look at first.
There are a few different wheel sizes for mountain bikes. 26”, 27.5” (650b) and 29” are the most common.
There is also plus (+) and fat versions available. If you are not sure it should be written on the side of the tyre.
Whatever wheel size you have, the fork must be designed to suit.
The fork steerer is attached to the fork crown, this comes up through the frame and headset to be clamped at the top by the stem.
Most modern bikes will have a tapered steerer, this is 1.5” inch wide at the fork and 1 1/8th inch at the stem. Some DH bikes and older mountain bikes will suit a straight 1 1/8th inch steerer.
It is easiest and best if the replacement fork has the same diameter steerer to fit into your frame and headset.
If you are unsure on the size, drop the forks out from the frame and you should be able to see straight away if the steerer is tapered or straight.
If you are planning on using the same front wheel with your new fork, the fork’s dropouts must suit your wheel.
The width of the front hub has traditionally been 100mm, with either a 9 or 15mm axle. With a 9mm Quick Release (QR), a fork could be described as 9mm x100mm or QR to fit. A larger 15mm bolt through axle is more common on higher end bikes, a fork could be described as 15 x 100 to suit. This 15mm axle can be a quick release style and can be referred to as 15QR
Over the last few years, a wider 110mm spacing known as “Boost” has become the new standard, this is not available for 9mm QR axles and would be shown as 15mm x 110 or 15mm Boost.
20mm axles have been common on DH bikes for some time. Although DH wheels will be 110mm wide, they are not always “Boost”. There is a new DH Boost for front wheels and forks, this means the hub is still 110mm wide, but the disc rotor/mount sits 5mm out.
The amount of distance the fork can move vertically is referred to as travel (shown in mm). The frame manufacturer will have designed the bike around a certain amount of travel. The general rule is to stay with this. Increasing or decreasing the fork travel can result in the geometry being severely compromised, making the bike handle worse than intended and putting more stress on the headtube structure.
*Changing fork travel can void frame warranty from the manufacturer, please check with the manufacturer before any travel increase/decrease.
As fork travel increases so can flex, to combat this a triple clamp design is used for forks with over 180mm of travel. The hub plus the two crowns creates a triple clamp. The forks are for DH use.
The distance the axle is offset from the steering axis. This directly affects the “Trail”. Trail is the distance between the contact point of the tyre and where the steering axis hits the floor. The shorter the offset the longer the trail and vice versa. Wheelsize also affects trail. Larger wheels have a longer trail. With the popularity of 29er MTB’s, there is often an offset choice to be made.
The most common offset for a 29er fork is 51mm, however, fork manufacturers offer shorter offsets to increase trail.
Once the correct fork has been chosen there are a few things you should know before fitting.
Crown race – Slid down over the steerer is the crown race, these are usually particular to the headset on your bike. They create a seat for the lower bearings of the headset to sit on, this should be removed from your forks and slid into place on the new fork steerer before installing the new forks.
Star Nut – Inside the steerer tube there is a star nut. This has a wedge design allowing it to be slid down into place but not slid back up. There is an internal thread that takes the top cap bolt allowing the forks to be held in place and allowing adjustment of the pressure on the bearings.
Steerer length – A new fork will have a long uncut steerer, this will more than likely need to be cut to match the length of your original forks, however, it can be cut longer or shorter if you wanted to have more adjustment for stem height.
See our full guide to setting sag here
Please note, all size information is provided as a guide - if you're unsure or need any further assistance you can call us on 01792 799508 ... we're happy to help!
Suspension Forks Guide
How do I apply for finance?
Spend £99 or more at Tredz and you can spread the cost. Pay monthly over 6-48 months, interest free (dependent on repayment terms and amount).
1Fill your basket with everything you want from Tredz and go to the checkout.
2During checkout, select the finance option you want as your method of payment.
3You will be sent to our finance provider's secure server to complete your application.
4Finance providers PayPal & V12 will use the information provided to make a decision and complete checkout if you are approved.Read more about buying on finance
Flexible finance options
Choose your deposit.
Choose your term.
Lowest monthly cost
for 48 months
Best £0 deposit / 0% interest
for 12 months
Delivery & Guarantee
UK Delivery Information
Courier Delivery update: Due to the COVID19 situation, we are currently experiencing some delays with deliveries. Our couriers are working around the clock to get your order to you as soon as possible but there is a potential delay of up to 48 hours . Please check your tracking on track your order here.
Please note on the TNT tracking app it may show your delivery status as ‘Collecting’ (as per image below). This means your delivery has left our warehouse and is currently held at TNT main depot and there could be up to a 48 hour delay.
Please keep checking the TNT tracking for further updates. On behalf of TNT we apologise for any delay and inconvenience this may cause.
We are committed to offering fast and free delivery, whether you're ordering bikes, accessories or clothing. Our standard delivery service is FREE in the UK, regardless of the size and on all orders over £20.
Please note that bulky products and bikes shipped to outlying UK regions are excluded from free shipping.
Please note that Pre-Order dates can sometimes change due to updated stock information.
Click here for more UK and international delivery information.
Returns & Warranty
It's easy to return a product with our 365 day, hassle free returns.
We will give you a full refund or exchange on any item that is returned to us unused/unfitted, in a resaleable condition and in its original packaging (where possible).
Please note: For hygiene reasons, we cannot accept returns of facemasks, undershorts or underwear if the item has been removed/unsealed from its original packaging.
If your item develops a fault or arrives damaged, please contact us first so we can resolve the issue for you as quickly as possible.
For more information please visit our Returns & Warranty page.
You may also like...
Finance provider options available